供应RF800T 免洗助焊剂

Alpha Metals RF800T 免洗助焊剂
No-Clean Flux 
 
 FEATURES     BENEFITS 
 
•  Medium Solids Content  • Pin Testable 
•  Non Corrosive Residues  •  High Sir Assemblies 
 
DESCRIPTION 
 
Alpha RF 800T  is a low solids, no-clean flux formulated with a small percentage of rosin and non-halide activators.  This unique rosin activation system promotes excellent wetting to protected copper and solder coated surfaces.  Post soldering residue of Alpha RF 800T is minimal, slightly glossy and can be pin tested without removal. 
  
USE 
 
Alpha RF 800T flux is formulated to be applied with foam, wave, spray and mist fluxers.  Flux deposition, density and uniformity are critical to successful use of low solids no-clean flux.  Applying RF 800T to a dry flux coating density of 100 to 300 micrograms per square centimetre is recommended.  Preheating the circuit assembly will partially dry the flux, enhance oxide removal and promote  optimum wicking, as well as superior solder joint formation.  Degree of preheat is dependent on many variables; such as conveyor speed, type of components and 
substrates.  Entering the solder wave with a top-side temperature of 90°C to 110°C and a bottom-side temperature of 120°C to 155°C is typical. 
 
The foam applicators should be supplied with compressed air, free of oil and water. Maintain flux fluid level sufficiently above the aerator to produce adequate foam height.  Adjust air pressure to produce optimum height with foam consisting of uniform bubbles.  The addition of flux thinners will be required to replace evaporative losses and maintain the balance in flux composition.  Due to the  low solids content of  Alpha RF 800T  flux, specific gravity is not an accurate measure for assessment.  Monitoring and controlling the acid number is recommended for maintaining the flux composition.  The acid number should be controlled between 21 and 22.  
In time, debris and contaminants will accumulate in recirculating type flux applicators. For consistent soldering performance, dispose of spent flux  in accordance with local bylaws, rules and regulations periodically. After emptying used flux, the reservoir and applicator should be thoroughly cleaned with flux thinner. Refill reservoir with fresh flux and allow a few minutes to stabilise before resuming soldering operation.  In this type of flux application equipment, replace flux every 3 days where used daily for eight hours or more. 
 
Although Alpha RF 800T is designed to be left on the board, if desired, post soldering residues can be removed with Alpha 2110  saponifier, Hydrex DX detergent or alternatively  a semi-aqueous process using Alpha Auto Clean 40 may be employed. 
 
Key factors for no-clean soldering: Start with clean boards and components. Maintain uniform flux coating. Separate boards to prevent flux carry-over.  
Parameters	Typical Values	Parameters/Test Method	Typical Values
Appearance      	Pale, yellow liquid	Recommended Thinner	800T Additive
Solids Content, wt/wt    	5.0	Shelf Life  	18 Months
Acid Number (mg KOH/g) 	21.6	Container Size Availability	20, 200L
Specific Gravity @ 25°C (77°F)  	0.800 ± 0.003	Bellcore TR-NWT-000078, Issue 3 Compliant	Yes
Flash Point (T.C.C.)    	13°C	IPC J-STD-004 Designation  	B (RO/L1)

深圳市汉泰电子材料有限公司长期供阿尔法系列（锡线，锡条，锡膏，助焊膏，助焊剂）千住系列（锡线，锡条，锡膏，助焊剂）阿米特系列（锡线，锡条，锡膏）乐泰系列（锡线，锡条，锡膏，底部填充胶，工业胶）减摩系列（锡线，锡条，锡膏）KOKI有铅无铅无卤无铅锡膏，TAMURA有铅无铅锡膏，铟泰有铅无铅无卤无铅锡膏，富士红胶，韩国130红胶，德邦底部填充胶等，如有需要欢迎各位来电咨询洽谈更多产品信息请登录hantaismt