供应ALPHA 265HF无卤素水溶性

ALPHA 265HF 无卤素水溶性助焊剂
HALIDE-FREE, LEAD TINNING FLUX 
 
GENERAL DESCRIPTION 
 
Alpha 265HF is a highly active, halide-free water-based organic acid type flux especially designed to give effective 
solder wetting with Kovar, Alloy 42, Nickel and is especially recommended for Copper and its alloys.  Besides 
providing high activity, ALPHA 265HF has the following features. 
 
i. Non-flammable – Fire hazards in wave soldering machines will be minimized; 
ii.  Slow evaporation rate – since deionized water is the primary solvent in this water-based flux, the specific gravity of such formulation will be more consistent over long periods of operation. 
iii.  Minimize bridging and provide even solder coating – due to the sustained activity and excellent wetting properties of the flux; ideally suited for soldering of closely spaced component leads, such as PLCC or SOIC etc. 
iv.  Can be used as received or diluted – depending on oxidation on lead surface.  In general, a dilution of flux with water or alcohol at 1:1 or 2:1 ratio by volume can be applied, making this flux particularly cost-effective. 
 
USES 
 
ALPHA 265HF is free from chlorides or bromides and is recommended for automatic wave soldering applications 
where there is a concern about the presence of halide activator in the flux.  This concern may arise from the possibility of either flux penetrating microcracks in component seals, or flux entrapment underneath, or in open or porous cavities of components, as all these conditions may cause detrimental effects to component reliability. 
 In addition, ALPHA 265HF is specially designed to give high activity and excellent surface tension properties which minimize or eliminate soldering defects, such as icicling, bridging and excessive solder.  ALPHA 265HF can be used as a flux for tinning conventional IC or component leads.  Moreover, the above special properties render the flux particularly suitable for lead tinning of flat packs, PLCCs and other SMDs.  
 
ALPHA 265HF can be applied by wave, dip, or spray techniques.  Foam applications is not recommended.  Besides, 
during wave soldering applications, preheating temperature using water-based 265HF flux should be higher than that normally used for alcohol-based fluxes to avoid spattering.  Alternatively, conveyor line speed might be lowered to drive out water in the flux.  The recommended lead preheat temperature is 100 ±  5○C. 
 
RESIDUES REMOVAL 
 
Residues from 265HF are completely soluble in water and hence cleaning of these residues can be accomplished with 
hot water.  For critical cleanliness requirements, final rinsing with deionized water may be required.
SPECIFICATIONS 
 
Property                                 Typical Value 
Appearance:                              Clear, amber liquid 
Specific Gravity @ 25○C (77○F)          1.192 ± 0.010 
Activation                                 Organic acid 
Flash Point (T.C.C.), as received             >200°F 
pH, as received                                 2.7 
5% solution in                                  3.0 
Water Solubility of Flux residues       Complete in warm water 
Total Halides, max.                           10 ppm  

THINNING 
 
No thinning is required since solvent evaporation from ALPHA 265HF is minimal.  However, Alpha 425 Thinner, which 
is an alcohol mixture, or deionized water can be used to adjust the viscosity or activity level of 265HF Fluxto suit a specific process.  Generally, Alpha 425 Thinner is recommended for dilution if there is problem of spattering.

深圳市汉泰电子材料有限公司长期供阿尔法系列（锡线，锡条，锡膏，助焊膏，助焊剂）千住系列（锡线，锡条，锡膏，助焊剂）阿米特系列（锡线，锡条，锡膏）乐泰系列（锡线，锡条，锡膏，底部填充胶，工业胶）减摩系列（锡线，锡条，锡膏）KOKI有铅无铅无卤无铅锡膏，TAMURA有铅无铅锡膏，铟泰有铅无铅无卤无铅锡膏，富士红胶，韩国130红胶，德邦底部填充胶等，如有需要欢迎各位来电咨询洽谈更多产品信息请登录hantaismt