• 进口减压阀使用寿命长德国洛克LOCKE品牌

    进口减压阀使用寿命长德国洛克LOCKE品牌

  • 2023-07-07 10:27 23
  • 产品价格:2850.00
  • 发货地址:广东省珠海市包装说明:不限
  • 产品数量:不限产品规格:不限
  • 信息编号:106375222公司编号:4282218
  • 叶伟新 销售经理
    +8613824185985 (联系我请说明是在阿德采购网看到的信息)
  • 进入店铺 在线咨询 QQ咨询
  • 信息举报
    产品描述

    进口减压阀使用寿命长德国洛克LOCKE品牌

     

    进口减压阀产品简介:

    德国洛克《DE LOCKE》进口减压阀是采用控制阀体内的启闭件的开度来调节介质的流量,将介质的压力降低,同时借助阀后压力的作用调节启闭件的开度,使阀后压力保持在一定范围内,并在阀体内或阀后喷入冷却水,将介质的温度降低,这种阀门称为减压减温阀。该阀的特点,是在进口压力不断变化的情况下,保持出口听压力和温度值在一定的范围内。

    Product introduction of imported pressure reducing valve:

    German Locke de lock imported pressure reducing valve regulates the flow of medium by controlling the opening of the opening and closing parts in the valve body to reduce the pressure of medium. At the same time, it adjusts the opening of the opening and closing parts with the help of the pressure behind the valve to keep the pressure behind the valve within a certain range, and injects cooling water into the valve body or behind the valve to reduce the temperature of medium. This valve is called pressure reducing and temperature reducing valve. The characteristic of the valve is to keep the outlet pressure and temperature within a certain range when the inlet pressure changes continuously.

     

    进口减压阀安装要求:

    在安装原装进口减压阀时,需要谨慎正规操作,具体安装要求如下:

    1、 原装进口减压阀安装前,需对管道进行试压、吹扫,保证管道的密封性与干净清洁。

    2、 原装进口减压阀应水平垂直安装在管道上,另安装时应注意使管路中介质的流向与阀体上所示箭头的方向一致。

    3、 原装进口减压阀两侧应安装控制球阀,并安装旁通管以备检修。

    4、 原装进口减压阀的高、低压管道上都应设置压力表,以便于调节,并可在运行中观察阀前和阀后的压力变化。

    5、 管道上设置安全放散阀,以保证原装进口减压阀运行的可靠性和安全性。

    6、 室内燃气管道应在室内设置燃气泄露报jing器装置,以保证燃气泄露危险时,能及时报警并排除险情。

    7、为了确保安全使用,在装好原装进口减压阀后,一定要测密封性,可在所有管道接口处使用检漏仪检测或刷肥皂水、洗洁精水进行检查,观察有无漏气。如在减压阀前后安装有压力表的,可关闭气源后,观察指针是否有变化。

    Installation requirements of inlet pressure reducing valve:

    When installing the original imported pressure reducing valve, it is necessary to operate carefully and normally. The specific installation requirements are as follows:

    1. Before installing the original imported pressure reducing valve, the pipeline shall be pressure tested and purged to ensure the tightness and cleanliness of the pipeline.

    2. The original imported pressure reducing valve shall be installed horizontally and vertically on the pipeline. In addition, during installation, pay attention to make the flow direction of the medium in the pipeline consistent with the direction of the arrow on the valve body.

    3. Control ball valves shall be installed on both sides of the original imported pressure reducing valve, and bypass pipes shall be installed for maintenance.

    4. Pressure gauges shall be set on the high and low pressure pipelines of the original imported pressure reducing valve to facilitate adjustment, and the pressure changes in front of and behind the valve can be observed during operation.

    5. A safety relief valve is set on the pipeline to ensure the reliability and safety of the original imported pressure reducing valve.

    6. Indoor gas pipeline shall be equipped with gas leakage alarm device indoors to ensure timely alarm and eliminate dangerous situations in case of gas leakage danger.

    7. In order to ensure safe use, the tightness must be tested after the original imported pressure reducing valve is installed. All pipeline interfaces can be tested with a leak detector or brushed with soapy water and detergent to observe whether there is air leakage. If a pressure gauge is installed before and after the pressure reducing valve, close the air source and observe whether the pointer changes.

     

    进口减压阀规格参数:

    1、公称压力:1.0MPa1.6MPa2.5MPa

    2、壳体试验压力:P=1.5PN

    3、密封试验压力:P=1.1PN

    4、出口压力: PN1.0MPa调节阀0.09~0.8MPa

    PN1.6MPa调节阀0.10~1.2MPa

    PN2.5MPa调节阀0.15~1.6MPa

     

    进口减压阀的选型: 

    减压阀进口压力的波动应控制在进口压力给定值的80%~105%,如**过该范围,减压阀的性能会受影响。

    1. 通常减压阀的阀后压力P2应小于阀前压力的0.5倍,即P2<0.5P1

    2. 减压阀的每一档弹簧只在一定的出口压力范围内适用,**出范围应更换弹簧。

    3. 在介质工作温度比较高的场合,一般选用先导式活塞式减压阀或先导式波纹管减压阀。

    4. 介质为空气或水(液体)的场合,一般宜选用直接作用薄膜式减压阀或先导式薄膜式减压阀。

    5. 介质为蒸汽的场合,宜选用先导活塞式减压阀或先导波纹管式减压阀。

    6. 为了操作、调整和维修的方便,减压阀一般应安装在水平管道上。

    根据使用要求选定减压阀的类型和调压精度,再根据所需*输出流量选择其通径。决定阀的气源压力时,应使其大于*输出压力01MPa。减压阀一般安装在分水滤气器之后,油雾器或定值器之前,并注意不要将其进、出口接反;阀不用时应把旋钮放松,以免膜片经常受压变形而影响其性能。







    莱恩泵阀制造(珠海)有限公司是一家经过国家相关部门批准的企业,凭着良好的信用、优良的服务与多家企业建立了长期的合作关系。本公司是一家销售进口阀门、进口泵浦、进口仪器仪表为一体的一站式材料供应商。本公司一级代理销售:德国《LOCKE》洛克、英国《SpiraxSarco》斯派莎克、日本《VENN》阀天、日本《KITZ》北泽、美国《KHK》、丹麦《GRUNDFOS 》格兰富水泵、瑞典《ITT》飞力水泵、德国《WILO》 威乐水泵、意大利 《DAB》水泵、美国《LAINE》莱恩等各大*品牌。
    
            本公司主导进口阀门有:进口蝶阀、进口球阀、进口闸阀、进口截止阀、进口止回阀、进口调节阀、进口减压阀、进口电磁阀、进口安全阀、进口疏水阀、进口隔膜阀、进口针型阀、进口过滤器、进口排气阀、进口平衡阀、进口低温阀门、进口水力控制阀、进口卫生级阀门等系列产品。
    主导进口泵浦有:进口多级泵、进口计量泵、进口转子泵、进口高温泵、进口隔膜泵、进口卫生泵、进口离心泵、进口真空泵、进口屏蔽泵、进口管道泵、进口化工泵、进口排污泵、进口消防泵等系列产品。
    主导进口仪器仪表有进口电磁流量计、进口涡街流量计、进口涡轮流量计、进口液位流量计、进口金属转子流量计、进口旋进旋涡流量计、防爆压力开关、智能压力传感器、不锈钢压力表、不锈钢温度表等系列产品。
    产品已覆盖全国各地,广泛用于消防系统,空调系统、**给排水、船舶,电力、石化、冶金等行业。
    
            我们本着"建立体系,持续改进,确保质量,热情服务,顾客满意"的质量方针,本着"创新+质量+诚信+服务"的企业精神,以"用户满意就是我们的追求"为宗旨,承诺:我们将以*的品质,合理的价格,齐全的品种和快捷的交货期向广大客户提供较优质的服务。 珠海莱恩泵阀热诚欢迎各界朋友前来参观、考察、洽谈业务。

    欢迎来到莱恩泵阀制造(珠海)有限公司网站,我公司位于生态环境优美,山水相间,陆岛相望,气候宜人的珠海市。 具体地址是广东珠海公司街道地址,负责人是叶伟新。
    主要经营进口电磁阀、进口疏水阀、进口闸阀、进口调节阀、进口减压阀、进口球阀、进口蝶阀、进口截止阀、进口闸阀、进口安全阀等等。
    单位注册资金:人民币 100 万元 - 200 万元。
    本公司在机械产品这一领域倾注了无限的热忱和激情,公司一直以客户为中心、为客户创造价值的理念、以品质、服务来赢得市场,衷心希望能与社会各界合作,共创成功,共创辉煌,携手共创美好明天!

    本页链接:http://www.cg160.cn/vgy-106375222.html
    以上信息由企业自行发布,该企业负责信息内容的完整性、真实性、准确性和合法性。阿德采购网对此不承担任何责任。 马上查看收录情况: 百度 360搜索 搜狗
莱恩泵阀制造(珠海)有限公司是一家经过国家相关部门批准的企业,凭着良好的信用、优良的服务与多家企业建立了长期的合作关系。本公司是一家销售进口阀门、进口泵浦、进口仪器仪表为一体的一站式材料供应商。本公司一级代理销售:德国《LOCKE》洛克、英国《SpiraxSarco》斯派莎克、日本《VENN》阀天、日本《KITZ》北泽、美..
相关分类
附近产地